Motorguide Removable Mounting Plate Bedienungsanleitung PDF herunterladen

Removable

Mounting Plate

For questions, contact Consumer Affairs at 1-920-929-5040

www.motorguide.com

90-8M4000705

Instruction Sheet

MGA501A1 Removable Mounting Plate

These instructions detail directions concerning mounting and usage of the removable mounting plate.

Kit Contents

• 1 Outer plate

• 1 Inner bar

• 1 Assembly pin

• 1 Hardware package

 ⌐2 ¼-20x15/8lengthPhillipspan-headscrew

 ⌐4 ¼-20x1½lengthPhillipspan-headscrew

 ⌐6 ¼-20x1lengthPhillipspan-headscrew

 ⌐6 ¼-20x2½lengthPhillipspan-headscrew

 ⌐18 flatwasher

 ⌐12 ¼nylocknut

 ⌐1 lock-ringpin

Mounting Instructions

Step 1. Remove the trolling motor from the mount.

Step 2. Remove the mount from the boat deck. Retain the hardware from this step. DO NOT THROW AWAY. Note the position of

  themountonthedeckandhowfarthemountextendspastthegunnel.

Step 3. Assemble the outer plate and inner bar. Insert the assembly pin through hole dtosecurethetwopieces.Positionthe

  assemblyontheboatdeck.Placethemountontopoftheassemblytoensureproperpositionofthemount. 

  (Dropintwopins/screwsifnecessarytokeeptheinnerbaralignedwiththeouterplate).Removethemountwhilehold-

ing the assembly in position. Mark the location of the inner bar holes onto the boat deck. Remove the assembly and drill a

  5/16”holeinthemarkedlocations.

Step 4. Attach the outer plate to the bottom of the mount using the appropriate holes as indicated above.

Note: The 07 mount (36” length) may require an additional set of holes drilled into the base of the mount.

3.1 Gator Flex: Usethe15/8”lengthand1½”lengthscrewsalongwiththewasherand  

lock nuts.

3.2 Gator 20 Series (07, 16 mount): Usethe1”lengthscrewsalongwiththewashersandnylocknuts.

Step 5. Attach the inner bar to the boat deck.

4.1 If your original mount DID NOT use rubber mount isolators, then re-use hardware from Step 2.

  4.2 IfyouroriginalmountDIDuserubbermountisolators,discardthemandusethe2½”screwswithwashersand

lock nuts.

Step 6. Set the mount, with its attached outer plate, over the secured inner bar. Slide the mount backwards to

engage the lip on to the inner bar.

Step 7. Slide the assembly pin through the outer plate and inner bar (through hole d).Securetheassembly  

pin by inserting the lock-ring pin through the end of the assembly pin.

Step 8. Install the trolling motor back onto the mount. Check for proper orientation at both the stowed and

deployed positions.

Removable 1
Mounting Plate 1

Inhaltsverzeichnis

Seite 1 - Mounting Plate

Kommentare zu diesen Handbüchern

Keine Kommentare

Motorguide Removable Mounting Plate Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Motorguide Removable Mounting Plate herunter. MotorGuide Removable Mounting Plate User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Motorguide Removable Mounting Plate